There are hundreds of different moulding profiles available, from stock patterns to custom cuts. Aside from those manufactured for special uses–door and window parts, or handrail and closet rods, for example–most interior mouldings can be divided into three basic functions:

Naturally, there are many other uses for mouldings as well, but this document will focus on those three. You'll find that if you master the techniques of installing these basic types of moulding, you'll be able to handle just about any trim job you encounter.

Moulding can be made out of a number of different materials–not all wood. Spruce and pine mouldings are the most common, because both are relatively inexpensive, and are also soft, fine-grained woods that can be worked easily and with a minimum of splitting and splintering.

You'll be able to find pine and spruce mouldings both in solid and fingerjointed (FJ) material. FJ mouldings are made from short lengths of wood glued end to end. FJ material is not only less expensive than solid moldings, but it also tends to be more resistant to warp. If you're planning on painting the trim rather than staining, FJ molding is a good choice.

Mouldings are also cut from oak, mahogany, birch, walnut and other hardwoods. Reproductions of old profiles are often manufactured from high-density polyurethane, although these products are expensive and tricky to work with and generally should be installed only by professionals.

Mouldings may be purchased unfinished, prefinished with stain and varnish or overlaid with a vinyl woodgrain print. Overlaid mouldings are often made from an engineered product such as particleboard or fiberboard. They are definitely a time-saver, but are generally less resistant to moisture than wood mouldings and should be avoided in high-moisture areas such as kitchens and bathrooms.

 

 


FIG. 1 - Mouldings come in a variety of patterns, depending on where they well be used.
A. Celling mouldings include crown (upper left), cove (upper right), and bed mouldings (lower right).
B. Common wall mouldings include cap mouldings (left) that trim out the top wainscot paneling, and chair rail (right).
C. Base mouldings include base shoe (far left column), base cap (second column) and base moulding (far right).
D. Windows and door mouldings include casing (top), and either rabbited or flat stools (bottom).

Base mouldings can be combined with base cap and base shoe to provide a decorative appearance.


FIG. 2 - Crown mouldings can be combined with square stock and base cap to create an architectural effect at the ceiling.


FIG. 3 - A window can be trimed out either with a stool at the bottom (top), or in a picture frame style with casing on all four sides.

 
FIG. 4 - Door casings may be mitered at the top (left), or–if the casing profile is equal thickness on both edges–butt-jointed (right).


TYPES OF MOULDINGS

  • There are three common types of ceiling moldings (Fig. 1). Cove molding is the simplest and most common. Crown and bed molding are decorative profiles that can provide a traditional appearance.
  • All come in various sizes, from 1/2" wide to over 5". Ceiling and other moldings can also be combined to create specific architectural treatments (Fig. 2).

  • When choosing ceiling moldings, remember that wide moldings tend to make the ceiling look lower; unless your ceiling is exceptionally high, use narrower moldings to avoid a claustrophobic look.

  • Base moldings also come in a variety of sizes and profiles (Fig. 1). Like ceiling moldings, they can be combined for a traditional look. Base moldings are often used in conjunction with a base cap, a small decorative profile that is applied on top of the base to finish the look.

  • Again, wider moldings tend to make a room look smaller, so avoid wide base moldings unless your rooms are spacious.

  • Casing is used around doors and windows (Fig. 1). Casing profiles often match base moldings, except casings are rounded on both front edges, while the lower edge of a base molding is square to keep dust out of the joint between the molding and the floor.

  • Windows may be trimmed two different ways at the bottom. Casing may be used on all four sides to create a "picture frame" look or a stool may be added with an apron below it (Fig. 3).

  • Casing is commonly mitered at the top of a door, but squared profiles may be butt-jointed (Fig. 4).



FIG. 5 - Door and window casings are installed with a 1/16" reveal between the edge of the jamb and the casing, which allows you to adjust the casing if the jamb is slightly out of plumb.


FIG. 6 - To cut a coped joint, first cut a 45-degree open miter at the end of the piece (far left). Then cut the piece at 90 degrees with a coping saw, following the edge of the first cut (center).

 
FIG. 7 - From top: A coped joint, a scarf joint, an outside miter.


FIG. 8 - Scarf joints should be cut and nailed directly over a stud.


WORKING WITH MOULDINGS

  • When trimming out a room, start with what finish carpenters call the "standing trim"–the door and window casings. The first step is to check to see if the edge of the jamb is flush with the wall surface; if it projects beyond the surface, you'll have to plane it flush. If the jamb is recessed, nail and glue a thin strip of material over the edge to bring it flush with the wall.

  • To trim a window, first cut the stool to length. The casings are set back from the face of the jamb about 1/16" on either side; this "reveal" is almost unnoticeable, but it allows you to adjust the casing slightly if the window is not quite plumb.

  • The first step is installing the stool. Measure the distance between the side jambs, then add 1/8" for both sides of the reveal, then add twice the width of the casing, then add 2- 1/2" so the stool will project 1-1/4" on each side. For example, if the jamb-to-jamb measurement of the window is 36" and you're using 2-1/4" casing, you'd cut the stool to 43-1/8" (36" + 1/8" + 2-1/4" + 2-1/4" + 2-1/2" = 43-1/8").

  • Measure up each side of the window from the stool to the head jamb (on a door, measure from the floor to the head jamb). If the dimensions are not equal, use the longer dimension. Add 1/16" and miter-cut the side casings with the short side of the miter matching your measurement. Position the side casings with a 1/16" reveal all along the length of the side jamb (Fig. 5) and nail them in place with 6d finish nails 24" on center. Use two nails at each location; drive one into the jamb and the other through the wall surface and into the stud.

  • Position a piece of casing over the head of the window, slightly longer than the outside edges of the side casings. Use the miter cut on the side to mark your cut on the head casing. Cut the head casing to length. Apply wood glue to the miters and set the head casing in place. Nail it to the jamb and wall as you did the side casings, then drive a 4d finish nail through the side casing into the end of the head casing on each side.
  • Once the door and windows are finished, you're ready to install the "running trim"–the ceiling and base moldings.

  • The first step is to locate the wall studs and mark their location on the wall just above the height of the baseboard with a light pencil mark. When you buy ceiling and base molding, try and buy lengths that will allow you to make complete runs without joints; if you can't do so, add 2' to any lengths that will be joined, so you can cut the joint over a stud.

  • To install base molding, start from any door. Measure from the door to the nearest wall. Cut the end of the first piece of base square, then measure the door-to-wall distance and cut the other end, also square. Nail the first piece in place with pairs of 6d finish nails driven into each stud and the floor plate it rests on.

  • The second piece of base will be joined to the first with a coped cut at the inside corner (Fig. 6). To make a coped cut, first cut the end of the piece at a 45-degree angle with the short side of the miter toward the face of the piece. Finish the cut with a coping saw, carefully following the cut edge along the face of the piece (Fig. 7).

  • Measure from the bottom of the first piece of base to the next corner, then square-cut the second piece at the other end so it butts into the corner. Repeat the process for each inside corner.

  • Use a miter cut at outside corners. Few outside corners are exactly 90 degrees, so you'll have to use a T-bevel to find the exact angle, then divide by two and cut each piece of base to that angle.

  • If you need to join two pieces of molding in the middle of a run, set the first piece in place and mark the centerpoint of the stud nearest to the end of the piece. Subtract half the thickness of the molding, then cut the end using an open miter cut (Fig. 7). Install the first piece, but don't nail over the last stud where the piece is mitered.

  • Cut a closed miter (Fig. 7) at the end of the second piece. Measure from the face of the first piece where the miter begins to the corner, then cut the second piece. Set it in place with the closed miter overlapping the open miter on the first piece. Apply glue to the joint and nail through both pieces into the stud (Fig. 8), then continue nailing to the corner.

  • Ceiling molding is installed much like base molding, except that ceiling molding is not applied flat against the wall. Instead, it covers the joint at a 45-degree angle.

  • If you have nothing but inside corners to deal with, the process is easy–simply install each piece with a square cut at one end and a coped cut at the other.

  • If you have outside corners, they'll have to be mitered. Again the process is simple, as long as you clamp the molding in the miter saw at the same 45-degree angle at which it will be installed.

  • To avoid damaging the surface of the moulding, drive the nail to within an 1/8" of the surface. Use a nail set to finish driving the nail. Putty can be used to fill the nail hole.

TOOL AND MATERIAL CHECKLIST
Moulding Steel Measuring Tape
Hammer Level
Nail Set Miter Box
Backsaw Coping Saw
Nails Putty Knife

Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the National Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document.

Ask for Other "Show-How" Instruction Sheets
Additional easy-to-use instruction sheets for home do-it-yourself projects are available from your local supplier of materials. Come in and ask for "Show-How" instructions when you get ready for that next handyman project!